OWNER'S MANUALIR Dome CameraPlease read this manual carefully before operating your set and retain it for future reference.MODEL LCV5300R-BNLCV5
10Part Names and Functionsh Setup menu control buttonsi Video Out connectorUse this jack for checking the picture with portable monitor when install
11ConnectionsBasic connectionThe peripheral devices (DVR, monitor, etc.), AC/DC adapter and cables are not supplied.1. Make the video signal connect
12Mounting the CameraNote:Refer the manual of Dome bracket adaptor when you mount the camera on the wall, pendant and parapet. Surface mountFollow the
133. Install the camera mounting bracket to the ceiling.FRONTPRODUCT CENTER POSITIONMEZ626877034 PlaceSELFTAPPING SCREWCABLE HOLE (LCV5300)CABLE HOLE
145. Assemble the camera and the housing. Make sure when you assemble the camera in the right direction. And then, assemble the dome cover and lens c
15Image AdjustmentYou can manually adjust the pan/tilt/azimuth angles, focus, and zoom while observing the connected monitor.Notes:t Do not hold the
163. Adjust the pan/tilt/rotate position of the camera.TILTTILTROTATEPA N4. Adjust the zoom.4-1. Unlock the zoom lever.4-2. Move the lever to adju
175. Adjust the focus.5-1. Unlock the focus lever.5-2. Move the lever to adjust the focus.5-3. Lock the lever.FARNEAR6. This camera utilizes an
18Menu OperationSETUPRIGHTLEFTDOWNt UP button:Used to move upper direction on the menu screen. Use this button to select an item or adjust the param-
19Menu OperationOSD Menu OverviewThe following table shows the list of menu items and op-tions. You can adapt the camera to your requirements by setti
2CAUTIONRISK OF ELECTRIC SHOCK DO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCKDO NOT REMOVE COVER (OR BACK)NO USER-SERVICEABLE PARTS INSIDER
20Menu OperationMOTION DETON EXITRET/ TOP / END3D-DNR 0 to 100 -PRIVACY MASKOFF -ONRECTANGLEMASK SELECTION1 to 8DISPLAYOFF / MOSAIC / COLOR1 to COLOR8
21Menu OperationSYSTEMFACTORY RESET -EXITRET/ TOP / ENDEXITRET/ TOP / ENDGeneral Operation1. Press [SET] button. The Main OSD menu screen appears on
22Menu Operationprevious setup menu.t RETURN: Return to the previous.Exposure SettingsYou can set the exposure options using the EXPOSURE menu.1. Se
23Menu Operationt HSBLC: Use for masking brightness of the specific area to view the subject more clearly. The HSBLC mode is automatically activated
24Menu OperationAGC (Automatic Gain Control) settingIf the images are too dark, change the maximum [AGC] value to make the images brighter. But noise
25Menu OperationSENS-UP settingIf pictures are not clear due to darkness, this SENS-UP operation would increase the sensitivity of picture. 1. Use [U
26Menu Operationbutton. t MANUAL: You can set the white balance options manually. > RED: Obtains the optimum amount of red gain. > BLUE: Obtain
27Menu Operation > LEVEL: Use [LEFT] or [RIGHT] button to select a level. > DWELL TIME: Use [LEFT] or [RIGHT] button to select a dwell time. t
28Menu Operationt SIZE ,/ : Enlarge or decrease the horizontal size of the prevent saturation zone.t SIZE ;. : Enlarge or decrease the vertical size
29Menu Operation3D-DNR Setting1. Select [3D-DNR] option. If pictures are not clear due to brightness, this option would reduce the noise of picture.2
3• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. D
30Menu OperationOFF, MOSAIC, COLOR 1 to COLOR 8 on the DISPLAY option. > Use [UP] or [DOWN] to select an option then use [LEFT] or [RIGHT] button t
31Menu Operation[SET] button to move the polygon on the [POSITION].Note:You can adjust the mask color manually except for color 8.Special Menu Setting
32Menu OperationD-ZOOM (Digital Zoom ) SettingYou can select the digital zoom level.1. Select [D-ZOOM] option on the [SPECIAL] menu. 2. Use [LEFT] o
33Menu Operationt MIRROR: Turn on the mirror effect.t OFF: Turn off the digital effect.SHARPNESS SettingThe degree to which the boundary of the two
34Menu OperationSYNC Setting1. Select [SYNC] option on the [SPECIAL] menu.2. The [SYNC] option is set to [INT] automatically.Note:AC24V Adaptor hav
35Menu Operationt A (Blank): Inserts a space at the cursor position.t / : Moves cursor to left or right.LANGUAGE SettingSelect the viewer language
36Item LCV5300R-BN LCV5300R-BPSignal System NTSC PALImage Device 6 mm (1/3 Type) Exview HAD CCD IITotal/Effective Pixels Number 520 000 Pixels / 480 0
37Item LCV5300R-BN LCV5300R-BPSmartIR IR Anti-SaturationBACKLIGHT BLC / HSBLC / OFFDNR 2D + 3D-DNRExposure ALC /ELCAuto Gain Control OFF/ LOW/ MIDDLE/
38SpecicationItem LCV5300R-BN LCV5300R-BPOperation Temperature/Humidity-10 ºC to 50 ºC / 0 % RH to 80 % RHStorage Temperature/ Humidity -20 ºC to 60
4Disposal of your old appliance1. All electrical and electronic products should be disposed of separately from the municipal waste stream via designat
51. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near wate
6Power SupplyThis camera must always be operated DC 12 V or AC 24 V.Certified/Listed Adaptor which comply with LPS.Handling of the unitBe careful not
7Features ... 8Accessories ...
8FeaturesThis IR Bullet Camera is designed for installation in a video surveillance system.This manual contains instructions on how to install and man
9Part Names and Functionsa Dome Coverb IR LEDc IR Sensord Focus lock leverFixes the focus position after adjusting. e Zoom lock leverFixes the zoom
Commentaires sur ces manuels