LG 65TC3D-B Manuel d'utilisateur télécharger pdf (Page 67)

ENGLISH

46. Status Check (Command: s v)

Checks the current signal of the product.

Transmission

[s][v][ ][Set ID][ ][Data][ ][FF][Cr]

Data 02: Checks whether there is a signal

03: The monitor is currently in PM Mode

05: Checks whether luminance sensors 1 and 2

are functioning properly.

06: Luminance sensors currently being used:

07: Checks whether the Top, Bottom and Main

temperature sensors are functioning normally.

08: The temperature of each temperature sensor

when the monitor set was last powered off.

09: Fan speed

10: RGB Sensing OK/NG (screen fault detection)

Acknowledgment

[v][ ][Set ID][ ][OK/NG][Data][Data1][x]

Data 02 (when a signal is found)

Data 1 00: No signal

01: Signal present

Data 03 (when the monitor is currently in PM mode)

Data 1 00: Screen On is activated.

01: Screen Off is activated.

02: Screen Off Always is activated.

03: Sustain Aspect Ratio is activated.

04: Screen Off & Backlight is activated.

Data 05 (when checking whether the luminance

sensors are functioning properly)

Data 1 00: All senors normal

01: BLU sensor 1 normal, BLU sensor 2 down

02: BLU sensor 1 down, BLU sensor 2 normal

03: All sensors down

Data 06 (when checking which luminance sensor is in

use)

Data 1 00: Luminance sensor 1 is in use.

01: Luminance sensor 2 is in use.

Data 07 (when checking whether the Top, Bottom and

Main temperature sensors are working properly)

Data 1 00: All temperature sensors faulty

01: Top normal, Bottom faulty, Main faulty

02: Top faulty, Bottom normal, Main faulty

03: Top normal, Bottom normal, Main faulty

04: Top faulty, Bottom faulty, Main normal

05: Top normal, Bottom faulty, Main normal

06: Top faulty, Bottom normal, Main normal

07: All temperature sensors are normal

Data 10 (when executing Screen Fault Detection)

Data 1 00: Screen Fault Detection result NG

07: Screen Fault Detection result OK

* When screen Fault Detection is set to Off or not supported,

execution results are rendered "NG."

Data (when checking the temperature of each

temperature sensor when the monitor set was

last powered off)

Acknowledgment

[v][ ][Set ID][ ][OK/NG][Data][Data1]

[Data2][Data3][x]

Data 1 The temperature of the Top sensor when the

monitor set was last powered off.

Data 2 The temperature of the Bottom sensor when the

monitor set was last powered off.

Data 3 The temperature of the Main sensor when the

monitor set was last powered off.

Data 09 (when checking the fan speed)

Acknowledgment

[v][ ][Set ID][ ][OK/NG][Data][Data1][Data2][x]

Data 1 00-ff: The upper 1-byte of the fan speed

Data 2 00-ff: The lower 1-byte of the fan speed

Fan speed: 0 to 2008 in hexadecimal and 0 to 8200 in

decimal

* This feature may not be supported on some models.

47. Screen Fault Detection (Command: t z)

Sets the Screen Fault Detection feature.

Transmission

[t][z][ ][Set ID][ ][Data][Cr]

Data 00: Off

01: On

Acknowledgment

[z][ ][Set ID][ ][OK/NG][Data][x]

* This feature may not be supported on some models.

1 2 ... 62 63 64 65 66 67 68 69 70 71 72 ... 90 91

Commentaires sur ces manuels

Pas de commentaire

LG 65TC3D-B Manuel d'utilisateur Page 67

Commentaires sur ces manuels

Produits connexes et manuels pour Non LG 65TC3D-B