LG WD-12401TDK Manuel d'utilisateur

9nstallationI Installation of drain hose• The drain hose should not be placedhigher than 100 cm above the floor.Water in the washer does not drain o

1. Adjusting the washing machine level properly prevents excessive noiseand vibration.Install the appliance on a solid and level floor surface, prefe

11are before washingC1. Care LabelsLook for a care label on your clothes. This will tell you about the fabric content of your garment andhow it should

12dding detergentA Adding detergent and fabric softener• Main wash only ➔• Pre Wash + Main Wash ➔• Do not exceed the maximum fill line.Close the dis

13dding detergentA• The detergent should be used according to theinstruction of the detergent manufacture.• If too much detergent is used, too many su

14unctionF Recommended courses according to the laundry type󳀌 Water Temperature : Select the water temperature to the wash cycles. Always follow gar

15ow to use washerH• Press the Power button to start.• Press the Start/Pause button.• Initial condition- Wash : Main wash- Rinse : 3 times- Spin : • 1

16ow to use washerH(1) Button : Power(2) Dial : Program(3) Button : Start/Pause(4) Button : Option(5) Child Lock(6) Button : Rinse(7) Button : Spin(8)

17ow to use washerHStart/PauseDoor LockOption• Lights whenever the door of the washer islocked.• The door can be unlocked by pressing theStart/Pause b

18ow to use washerHRinse• By pressing the Rinsebutton,the Rinse type canbe selected.Child lockIf you choose to lock the buttons on thecontrol assembly

WD-1440(0~9)TDKWD-1240(0~9)TDKWD-1040(0~9)TDK

• Spin speed is available according to theprogramas follows.WD-1040(0~9)TDK- Cotton & Cotton-Eco & Quick 30 No Spin – 400 – 600 – 800 – 1000-

20ow to use washerHWater Temp.• Water temperature can be selected asbelow according to the program.- Cotton-Eco40°C – 60°C- Cotton Cold – 30°C – 40°C

21ow to use washerH• If the washer encounters a fault duringoperation, the associated fault will bedisplayed.“” : Water pressure sensing error“” : Pro

22 The water inlet filter- " " error message will blink on the control panel when water does not enter thedetergent drawer.- If w

23aintenanceM2332321100 The drain pump filter❋ The drain filter collects threads and small objects left in the laundry.Check regularly that the filte

24aintenanceM Dispenser drawer󳀌 After a while detergents and fabric softeners leave a deposit in the drawer.• It should be cleaned from time to time

25aintenanceMCleaning your washer1. ExteriorProper care of your washer can extend its life.The outside of the machine can be cleaned with warm water

26roubleshooting guide󳀌This washing machine is equipped with automatic safety functions which detect and diagnose faults at aearly stage and react app

27Washer does not startWasher won’t spinDoor does not openWash cycle timedelayed• Electrical power cord may notbe plugged in or connectionmay be loose

28roubleshooting guideSymptom Possible Cause Solution• Water supply is not adequate in area• Water supply taps are not completelyopen.• Water inlet ho

2roduct FeaturePontentsCDirect Drive SystemThe advanced Brushless DC motor directly drives the drum withoutbelt and pulley.Built-in HeaterInternal hea

29erms of WarrantyTWhat is Not Covered : • Service trips to your home to teach you how to use the product.• If the product is connected to any voltage

30emoM

arningsWREAD ALL INSTRUCTIONS BEFORE USEFor your safety, the information in this manual must be followed to minimizethe risk of fire or explosion, ele

4pecificationS Accessories󳀎The appearance and specifications may be varied without notice to raise the units quality. Name : Front loading washing

5nstallationI1. To prevent internal damage duringtransport, the special 4 bolts are locked.Before operating the washer, remove the bolts along with th

6nstallationILevel floor :Allowable slope under entire washer is 1˚Power outlet :Must be within 1.5 meters of either side of location ofwasher. Do not

7nstallationI▶Water supply pressure must be between 30kPa and 1000kPa(0.3~10kgf/cm2)▶Don’t strip or crossthread when connecting Inlet hose to the valv

8nstallationI Normal Tap without thread & screw type inlet hose Normal Tap without thread & one touch type inlet hose 1. Unscrew the fixing