www.lg.comOWNER’S MANUALMONITOR SIGNAGEMONITOR SIGNAGE MODELSM3704CPlease read this manual carefully before operatingyour set and retain it for future
10Select an input signal.Press the INPUT button on the remote control to select the input signal. Or, press the INPUT button on the back of the produ
11• Using LAN establishes communication between your PC and the monitor and enables to use the OSD menus on the PC as well as on the monitor.NoteConn
12Connecting to External DevicesDaisy Chain Monitors When using RGB input When using AV input To use different products connected to each other Conne
13Kensington Security Slot The Set is equipped with a kensington Security System connector on the back panel. The cable and lock are available separat
14Connecting to External DevicesWhen connecting with an BNC cable.• Select AV. Connect the video cable as shown in the below figure and then connect
15• Select Component.Connect the video/audio cable as shown in the below figure and then, connect the power cord (See page 10).• Connect the input ter
16Connect the video/audio cable as shown in the below figure and then connect the power cord (See page 10).RCA-PC Audio Cable(not included)ProductVCR/
17User MenusScreen Adjustment optionsPress this button to turn on the power. Press this button again to turn it off.This Indicator lights up green whe
18User MenusThis is where the unit receives signals from the remote control.Screen Adjustment options[For PC Analog signal]AUTO/SET Button AV Composi
19OSD Menu NoteOSD(On Screen Disp lay)• The OSD function enables you to adjust the screen status conveniently since it provides graphical presentatio
2Table of ContentsAccessories 3Connecting the stand 4Connecting the Speakers 5Using the Remote Control 6Name and Function of the Parts 8Connecting
20User MenusHow to adjust the OSD (On Screen Display) screen• Use the remote control to adjust the OSD screen.How to adjust the screen automaticallyPr
21User MenusAdjusting Screen ColorAspect RatioMoveOKPICTUREAspect Ratio : 16:9 Energy Saving : OffPicture Mode : Standard • Backlight 70 •
22MoveOKPICTUREAspect Ratio : 16:9ꕫ Energy Saving : OffPicture Mode : Standard • Backlight 70 • Contrast 90 • Brightness 50 • Sharpn
23Adjusting Screen ColorUser MenusPicture ModeMoveOKPICTUREAspect Ratio : 16:9 Energy Saving : OffPicture Mode : Standard • Backlight 70 •
24User MenusMoveOKPICTUREAspect Ratio : 16:9 Energy Saving : OffPicture Mode : Standard (User) • Backlight 70 • Contrast 90 • Brightn
25User MenusMoveOKPICTURE ▲ • Contrast 90 • Brightness 50 • Sharpness 70 • Color 60 • Tint 0 • Advanced Control • Picture ResetSc
26User MenusMoveOKPICTURE ▲ • Contrast 90 • Brightness 50 • Sharpness 70 • Color 60 • Tint 0 • Advanced Control • Picture ResetSc
27Adjusting the audio functionUser MenusMoveAUDIOAuto Volume : OffClear Voice II : Off • Level 3Balance 0Sound Mode : Standard • Treble
28Adjusting the timer functionUser MenusMoveTIMEOKClockOff Time : OffOn Time : OffSleep Timer : OffAuto Off : OnPower On Delay : OffClock
29User MenusMoveOPTIONOKLanguage : EnglishInput Label Key Lock : OffSet ID : OffISM Method : NormalDPM Select : OnPower Indicator : O
3Without prior notice, optional accessories are subject to change to improve the performance of the product, and new accessories may be added.❖ Option
30User MenusMoveOPTIONOK ▲ISM Method : NormalDPM Select : OnPower Indicator : ONLogo Light : ONInterface S
31Tile mode and choose Tile alignment and set the ID of the current product to set location.Only after pressing the SET button the adjustments made to
32- Tile mode (product 1 ~ 2) : c(2) x r(1)- Tile mode (product 1 ~ 9) : c(3) x r(3)- Tile mode (product 1 ~16) : c(4) x r(4)rowcolumnID 1ID 5ID 9ID 1
33User MenusAdjusts the USB options.When connecting the USB deviceWhen you connect a USB device, this pop up menu is displayed, automatically.“POP UP
34User MenusAdjusts the USB options. Precautions when using the USB device• Only a USB storage device is recognizable.• If the USB storage device
35User MenusAdjusts the USB options.You can view photo files on USB storage device.The On Screen Display may be different from your SET. Images are an
36Photo ListPage 2/3Drive1JMJ0011366x768, 125KBUp FolderUp FolderKY101 02/12/2010KY102 02/12/2010JMJ001 02/12/201
37User MenusAdjusts the USB options.◄ 1/17 ►Slideshow ◘ BGM ◘ Delete Option Hide꘤ ► Slideshow When no picture is selected, all pho
38User MenusYou can play music files on USB storage device.Purchased music files(*.MP3) may contain copyright restrictions. Playback of these files ma
39Music Selection and PopUp Menu➩As shown, up to 6 music titles are listed per page.User MenusAdjusts the USB options.Music ListPage 2/3MusicS00300:00
4Connecting the stand- Only on some models.2.3.1.Take the parts for the stand out of the box and assemble them as shown in the picture. Place a soft
40MusicS0030:27 / 3:67If you don't press any button for a while during the playing, the play information box (as shown in the below) will float a
41The movie list is activated once USB is detected. It is used when playing movie files on SET.Displays the movies in the USB folder and supports Play
42User MenusAdjusts the USB options.Page 2/3MovieM002640x480, 720KBUp FolderTitle DurationUp FolderFavorite MusicM001M002M001M00101:34:1501:35:3001:30
43Movie Selection and PopUp Menu➩User MenusAdjusts the USB options.Page 2/3MovieM002640x480, 720KBUp FolderTitle DurationUp FolderFavorite MusicM001M0
44User MenusAdjusts the USB options.When you select the Movie Option,Picture Size : Sets to [Full] or [Original].Subtitle Language : Allows to select
45User MenusMoveUSBOKPhoto ListMusic ListMovie ListDivX Reg. CodeDeactivationDivX Reg. Code ꔋAdjusts
46MoveUSBOKPhoto ListMusic ListMovie ListDivX Reg. CodeDeactivationDeactivation ꔋDeactivation T
47Troubleshooting• The control locking function prevents unintentional OSD setting change due to careless usage. To unlock the controls, simultaneous
48Troubleshooting● Is the screen position wrong?● Do thin lines appear on the background screen?● Horizontal noise appears or the characters
49Troubleshooting• Set the number of colors to more than 24 bits (true color) Select Control Panel - Display - Settings - Color Table menu in Wind
5Connecting the SpeakersMount the product onto the speaker by using a screw as shown in the following connect the speaker cable.When the speaker is in
50Specifi cations Note• The specifications shown above may be changed without prior notice for quality improvement.LCD PanelPower Dimensions& Wei
51 Specifi cations Note• The specifications shown above may be changed without prior notice for quality improvement.Max. Resolution RGB : 1920 x
52 Specifi cations PC Mode - Preset ModeNote• DTV/PC selection on HDMI/DVI inputs is available for PC resolutions : 640 x 480/60 Hz, 1280 x 720/60 Hz
Controlling the Multiple ProductRS-232CA1A1Connecting the cableConnect the RS-232C cable as shown in the picture. You need to purchase a cable to con
Controlling the Multiple ProductRS-232CA2 '311%2('311%2((%8%
Controlling the Multiple ProductRS-232CA3 '311%2('311%2((%8%
Controlling the Multiple ProductRS-232CA4OK Acknowledgement * The Product transmits ACK (acknowledgement) based on this format when receiving normal
Controlling the Multiple ProductRS-232CA5Transmission / Receiving Protocol01. Power(Command : a)►To control Power On / Off of the Set.TransmissionDat
Controlling the Multiple ProductRS-232CA603. Aspect Ratio(Command : c) (Main picture format)►To adjust the screen format. You can also adjust the
Controlling the Multiple ProductRS-232CA7A705. Volume Mute(Command : e) ►To control On/Off of the Volume Mute.TransmissionData 0 : Volume Mute On (V
6Using the Remote ControlName of the Remote Control Buttons12534769813121110Power On / Off Button- Switches the set on from standby or off to standby.
Controlling the Multiple ProductRS-232CA8A8Transmission / Receiving Protocol07. Contrast(Command : g)►To adjust screen contrast. You can also adj
Controlling the Multiple ProductRS-232CA9Transmission / Receiving Protocol09. Color(Command : i) (Video Timing only)►To adjust the screen color. Y
Controlling the Multiple ProductRS-232CA1011. Sharpness(Command : k) (Video Timing only)► To adjust the screen Sharpness. You can also adjust the
Controlling the Multiple ProductRS-232CA11Transmission / Receiving Protocol14 Balance(Command : t)►To adjust the sound balance.TransmissionData Min
Controlling the Multiple ProductRS-232CA12Transmission / Receiving Protocol16. Abnormal state (Command : z)►Abnormal State : Used to Read the power o
Controlling the Multiple ProductRS-232CA1318. Auto Configure(Command: j u)►To adjust picture position and minimize image shaking automatically. it
Controlling the Multiple ProductRS-232CA1420. Tile Mode(Command : d d)►Change a Tile Mode.Transmission* The data can not be set to 0X or X0 except 00
Controlling the Multiple ProductRS-232CA1521. Tile H Position(Command : d e)►To set the Horizontal position. TransmissionData Min : 00H to Max : 14H
Controlling the Multiple ProductRS-232CA1623. Tile H Size(Command : d g)►To set the Horizontal size. TransmissionData Min : 00H to Max : 64H* Refer
Controlling the Multiple ProductRS-232CA17A1725. Tile ID Set(Command : d i)►To assign the Tile ID for Tiling function . TransmissionData Min : 00H t
7Energy Saving Button- Adjust the Energy Saving mode of the SET.INPUT Select ButtonIf you press the button once, the following Input Signal Window wil
Controlling the Multiple ProductRS-232CA18A18Transmission / Receiving Protocol28. Sound Mode (Command : d y )►To adjust the Sound mode. Transmission
Controlling the Multiple ProductRS-232CA19Controlling the Multiple ProductRS-232CA1931. Temperature value (Command : d n) ►To read the inside tempera
Controlling the Multiple ProductRS-232CA20Controlling the Multiple ProductRS-232CA2033. Auto volume (Command : d u) ►Automatically adjust the volume
Controlling the Multiple ProductRS-232CA2135. Time (Command : f a) ►Set the current time. Transmission[Data1]0 : Monday1 : Tuesday2 : Wednesday3 : T
Controlling the Multiple ProductRS-232CA22Transmission / Receiving ProtocolTransmission [Data1]1. f1h to f4h(read one index) f1: read 1st
Controlling the Multiple ProductRS-232CA23Transmission[Data 1]1. f1h to f4h(read one index) f1: read 1st index of Off Time List,
Controlling the Multiple ProductRS-232CA24Transmission / Receiving Protocol38. Scheduling Input select (Command : f u) (Main Picture Input)►To select
Controlling the Multiple ProductRS-232CA2539. Sleep Time (Command : f f) ►Set Sleep Time. Transmission Data 0 : Off1 : 102 : 203 : 304 : 605
Controlling the Multiple ProductRS-232CA2641. Power On Delay (Command : f h) ► Set the schedule delay when the power is turned on (Unit: second). Tra
Controlling the Multiple ProductRS-232CA2743. DPM Select (Command : f j) ►Set the DPM (Display Power Management) function. TransmissionData 0 : Off
8Name and Function of the PartsRear View* LINE OUT A terminal used to connect to the speaker including a built-in amplifier (Amp). Make sure that t
Controlling the Multiple ProductRS-232CA2845. Power saving(Command : f I) ►To set the Power saving mode. Transmission Data 0 : Off 1:
Controlling the Multiple ProductRS-232CA29Transmission / Receiving Protocol47. logo Indicator (Command : f p) ►To set the LED for Power IndicatorTran
Controlling the Multiple ProductRS-232CA3049. S/W Version (Command : f z) ►Check the software version. Transmission Data FFH : ReadAcknowledg
IR CodesRS-232CA31 Remote Control IR Code Output waveform single pulse, modulated with 37.917kHz signal at 455kHz ►Configuration of frameT1
IR CodesRS-232CA32'SHI,I\*YRGXMSR2SXI94ȗ(3;2ț6-+,8ș0)*8ȝ43;)6323**
IR CodesRS-232CA33))&&&&%*)%&*('%*6'&YXXSR6'&YXXSR6'&YXXSR6'
Make sure to read the Safety Precautions before using the product.Keep the Owner's Manual(CD) in an accessible place for future reference.The mod
9First of all, see if the computer, product and the peripherals are turned off. Then, connect the signal input cable.When connecting with the D-Sub si
Commentaires sur ces manuels