LG ARUM160LTE5.EWGBLEU Manuel d'utilisateur télécharger pdf (Page 7)

ENGLISH

SELECT THE BEST LOCATION

Select space for installing outdoor unit, which will meet the following

conditions:

• No direct thermal radiation from other heat sources

• No possibility of annoying neighbors due to noise of unit

• No exposition to strong wind

• With strength which bears weight of unit

• Note that drain flows out of unit when heating

• Because of the possibility of fire, do not install unit to the space

where generation, inflow, stagnation, and leakage of combustible gas

is expected.

ALTERNATIVE REFRIGERANT R410A

The refrigerant R410A has the property of higher operating pressure in

comparison with R22.

Therefore, all materials have the characteristics of higher resisting

pressure than R22 ones and this characteristic should also be consid-

ered during the installation.

R410A is an azeotrope of R32 and R125 mixed at 50:50, so the ozone

depletion potential (ODP) of R410A is 0.

CAUTION

• The above list indicates the order in which the individual work

operations are normally carried out but this order may be varied

where local conditions warrants such change.

• The thickness of the piping should comply with the relevant

local and national regulations for the designed pressure 3.8 MPa

(551.1 psi).

• Since R410A is a mixed refrigerant, the required additional re-

frigerant must be charged in its liquid state.(If the refrigerant is

charged in its gaseous state, its composition changes and the

system will not work properly.)

CAUTION

Notes : * We can guarantee the operation only within 130%

combination. If you want to connect more than 130%

combination, please contact us and discuss the re-

quirement like below.

• If the operation of indoor unit is more than 130%, the airflow is

operated as low in the all indoor units.

Combination Ratio(50~200%)

Outdoor Number Connection Ratio

Single outdoor units 200%

Double outdoor units 160%

Triple outdoor units 130%

Over the triple unit 130%

CAUTION

• The wall thickness of the piping should comply with the relevant

local and national regulations for the designed pressure 3.8MPa

[551.1psi]

• Since R410A is a mixed refrigerant, the required additional re-

frigerant must be charged in its liquid state.

If the refrigerant is charged in its gaseous state, its composition

changes and the system will not work properly.

• Do not place the refrigerant container under the direct rays of

the sun to prevent it from exploding.

• For high-pressure refrigerant, any unapproved pipe must not be

used.

• Do not heat pipes more than necessary to prevent them from

softening.

• Be careful not to install wrongly to minimize economic loss be-

cause it is expensive in comparison with R22.

OUTDOOR UNITS INFORMATION

The foundation must be level even

Outdoor unit foundation work

Avoid short circuits and ensure

sufﬁcient space is allowed for service

Installation of outdoor unit

Refer to automatic addressing ﬂowchart

Automatic addressing of indoor unit

In the ﬁnal check for 24hours at 3.8MPa (38.7 kgf/cm

)[551.1psi]

there must be no drop in pressure.

Airtight test

Multiple core cable must not be used.

(suitable cable should be selected)

Electrical work

(connection circuits and drive circuits)

Make sure no gaps are left where

the insulating materials are joined

Heat insulation work

Make sure airﬂow is sufﬁcient

Duct work

Adjust to downward gradient

Drain pipe work

Special attention to dryness,

cleanness and tightness

Refrigerant piping work

Check model name to

make sure the ﬁtting

is made correctly

Installation of indoor unit

Take account of gradient

of drain piping

Sleeve and insert work

Make connection clearly between outdoor, indoor,

remote controller and option.

Preparation of contract drawings

Indicate clearly who will be responsible for switch setting.

Determination of division work

The vacuum pump used must have a capacity of reaching at least

5 torr, more than 1 hour

Vacuum drying

Recharge correctly as calculated in this manual. and record the

amount of added refrigerant

Additional charge of refrigerant

Make sure there are no gaps left between the facing materials

used on the ceiling

Fit facing panels

Run each indoor unit in turn to make sure the pipe work

has been ﬁtted correctly

Test run adjustment

Explain the use of the system as clearly as possible to your customer and

make sure all relevant documentation is in order

Transfer to customer with explanation

Preheat the crank case with the electrical heater for more than 6 hours.

INSTALLATION PROCESS

1,MFL67221433,영어 2017. 7. 5. 오전 10:30 페이지 7

1 2 3 4 5 6 7 8 9 10 11 12 ... 54 55

Commentaires sur ces manuels

Pas de commentaire

LG ARUM160LTE5.EWGBLEU Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Pompes à chaleur LG ARUM160LTE5.EWGBLEU